无忧启动论坛
标题:
PE手动添加RAID驱动问题
[打印本页]
作者:
vacheli
时间:
2014-12-31 09:58
标题:
PE手动添加RAID驱动问题
我想手动添加raid驱动到PE里面,打开.inf文件我根本找不到什么[HardwareIdsDatabase],请大家帮我看一下我的.inf文件。
; Copyright (c) 2009-2012 Intel Corporation
; **********************************************************************************************
; **********************************************************************************************
; ** Filename: iaStorS.inf
; ** Revision: 10/18/2012,3.6.0.1086
; ** Abstract: Windows* INF File for SCU Intel(R) Rapid Storage Technology Enterprise Driver
; ** Installs: RSTe SCU RAID Controller Miniport + RST Filter Driver
; **********************************************************************************************
;
[Version]
Signature = "$Windows NT$"
Class=SCSIAdapter
ClassGUID={4D36E97B-E325-11CE-BFC1-08002BE10318}
Provider=%INTEL%
CatalogFile=iaStorS.cat
DriverVer=10/18/2012,3.6.0.1086
;
[PackageInfo]
Name=SCU
;
[SourceDisksNames]
1 = %DiskId1%,,,""
;
[DestinationDirs]
DefaultDestDir = 12
;
[ControlFlags]
ExcludeFromSelect = *
;
[Manufacturer]
%INTEL% = INTEL, NTx86.5.2, NTamd64
;
[Intel_SCU_iaStorS_Service_Inst]
ServiceType = %SERVICE_KERNEL_DRIVER%
StartType = %SERVICE_BOOT_START%
ErrorControl = %SERVICE_ERROR_NORMAL%
ServiceBinary = %12%\iaStorS.sys
LoadOrderGroup = SCSI Miniport
AddReg = pnpsafe_pci_addreg
AddReg = UserParameters
;AddReg = msienable_addreg
;
[Intel_SCU_EventLog_Inst]
AddReg = Intel_SCU_EventLog_Inst.AddReg
;
[Intel_SCU_EventLog_Inst.AddReg]
HKR,,EventMessageFile,%REG_TYPE_EXPAND_SZ%,"%%SystemRoot%%\System32\IoLogMsg.dll;%%SystemRoot%%\System32\drivers\iaStorS.sys"
HKR,,TypesSupported,%REG_TYPE_DWORD%,7
;
[iaStorF_Service_Inst]
ServiceType = %SERVICE_KERNEL_DRIVER%
StartType = %SERVICE_BOOT_START%
ErrorControl = %SERVICE_ERROR_NORMAL%
ServiceBinary = %12%\iaStorF.sys
;
[iaStorF_EventLog_Inst]
AddReg = iaStorF_EventLog_AddReg
;
[iaStorF_EventLog_AddReg]
HKR,,EventMessageFile,%REG_TYPE_EXPAND_SZ%,"%%SystemRoot%%\System32\IoLogMsg.dll"
HKR,,TypesSupported,%REG_TYPE_DWORD%,7
;
;******************************************************************************
;*
;* 32-BIT X86 ARCHITECTURE
;*
;* This section specifies the 32-bit architecture specific INF file entries
;* required to install a driver as a 32-bit compatible driver.
;*
;******************************************************************************
[SourceDisksFiles.x86]
iaStorS.sys = 1,,,
iaStorF.sys = 1,,,
;
[INTEL.NTx86.5.2]
;;; SCU 0 Device IDs
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D60
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D61
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D64
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D65
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D68
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D69
%Intel_SATA_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D6A
%Intel_SATA_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D6B
;
[Intel_SCU_iaStorS_Inst.NTx86]
CopyFiles = @iaStorS.sys
CopyFiles=@iaStorF.sys
;
[Intel_SCU_iaStorS_Inst.NTx86.HW]
AddReg = iaStorF_addreg
AddReg = msienable_addreg
AddReg = storport_addreg
Include = machine.inf
Needs = PciIoSpaceNotRequired
;
[Intel_SCU_iaStorS_Inst.NTx86.Services]
AddService = iaStorS,%SPSVCINST_ASSOCSERVICE%,Intel_SCU_iaStorS_Service_Inst, Intel_SCU_EventLog_Inst
AddService = iaStorF, , iaStorF_Service_Inst, iaStorF_EventLog_Inst
;
;******************************************************************************
;*
;* 64-BIT X86 ARCHITECTURE
;*
;* This section specifies the 64-bit architecture specific INF file entries
;* required to install a driver as a 64-bit compatible driver.
;*
;******************************************************************************
[SourceDisksFiles.amd64]
iaStorS.sys = 1,,,
iaStorF.sys = 1,,,
;
[INTEL.NTamd64]
;
;;; SCU Device IDs
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D60
%Intel_SATA_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D61
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D62
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D63
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D64
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D65
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D66
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D67
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D68
%Intel_SAS_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D69
%Intel_SATA_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D6A
%Intel_SATA_RAID.Desc% = Intel_SCU_iaStorS_Inst,PCI\VEN_8086&DEV_1D6B
;
[Intel_SCU_iaStorS_Inst.ntamd64]
CopyFiles = @iaStorS.sys
CopyFiles=@iaStorF.sys
;
[Intel_SCU_iaStorS_Inst.ntamd64.HW]
AddReg = iaStorF_addreg
AddReg = msienable_addreg
AddReg = storport_addreg
Include = machine.inf
Needs = PciIoSpaceNotRequired
;
[Intel_SCU_iaStorS_Inst.ntamd64.Services]
AddService = iaStorS,%SPSVCINST_ASSOCSERVICE%,Intel_SCU_iaStorS_Service_Inst, Intel_SCU_EventLog_Inst
AddService = iaStorF, , iaStorF_Service_Inst, iaStorF_EventLog_Inst
;
;******************************************************************************
;*
;* RST FILTER Driver REGISTRY CHANGES
;*
;* This section specifies the registry entries necessary to add the lower disk
;* class RST Filter driver. Layer the RST Filter driver under all Disk class
;* GUID devices as a lower disk class filter..
;*
;******************************************************************************
[iaStorF_addreg]
HKLM, System\CurrentControlSet\Control\Class\{4d36e967-e325-11ce-bfc1-08002be10318}, LowerFilters, 0x00010008, iaStorF
;
;******************************************************************************
;*
;* PLUG-N-PLAY REGISTRY CHANGES
;*
;* This section specifies the registry entries necessary to indicate support
;* for Plug-n-Play.
;*
;******************************************************************************
[pnpsafe_pci_addreg]
HKR, Parameters\PnpInterface, 5, %REG_TYPE_DWORD%, 0x00000001
;
; BusType 0xA == BusTypeSas (winioctl.h)
; PCI subclass code indicates SAS (not RAID), so for WHQL, the BusType
; needs to match
HKR, Parameters, BusType, %REG_TYPE_DWORD%, 0x0000000A
HKR, Parameters\Device, EnableQueryAccessAlignment, %REG_TYPE_DWORD%, 0x00000001
;******************************************************************************
;*
;* MSI/MSI-X REGISTRY CHANGES
;*
;* This section specifies the registry entries necessary in order to indicate
;* this driver supports MSI-X.
;*
;******************************************************************************
[msienable_addreg]
;;; Indicate we support MSIx up to 2 message vectors
;HKR, Interrupt Management, , %REG_TYPE_KEY_ONLY%
HKR, Interrupt Management, 0x00000010
HKR, Interrupt Management\MessageSignaledInterruptProperties, 0x00000010
HKR, Interrupt Management\MessageSignaledInterruptProperties, MSISupported, %REG_TYPE_DWORD%, 1
[storport_addreg]
;;; Force StorPort to keep all sense data in Pre-Win8 OSes (max value is 255)
HKR, StorPort, TotalSenseDataBytes, %REG_TYPE_DWORD%, 0x000000FF
;******************************************************************************
;*
;* USER PARAMETER REGISTRY CHANGES
;*
;* This section specifies the parameters that users can modify in the
;* registry that will change the operation of the driver after a power
;* cycle of the system or a reinstall of the driver.
;*
;******************************************************************************
[UserParameters]
;;; Build the Registry Directories
HKR, Parameters, Device, %REG_TYPE_KEY_ONLY%
;
;;; Add the RAID features
HKR, Parameters\Device, ReadPatrol, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, RebuildOnHotInsert, %REG_TYPE_BINARY%, 0x00000000
;
;;; Add the Controller wide user parameters
HKR, Parameters\Device, ControllerDeviceSpinUpDelayInterval, %REG_TYPE_DWORD%, 0x000001F4
HKR, Parameters\Device, ControllerInterruptCoalescenceNumber, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, ControllerInterruptCoalescenceTimer, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, ControllerSataNcqEnable, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, ControllerSataNcqDepthMaximum, %REG_TYPE_DWORD%, 0x00000020
HKR, Parameters\Device, ControllerSataStandbyTimerEnable, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, ControllerSataNonZeroBufferOffsetEnable, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, ControllerInitialResetType, %REG_TYPE_DWORD%, 0x00000008
HKR, Parameters\Device, ControllerClearAffiliationEnable, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, StpInactivityTimeout, %REG_TYPE_DWORD%, 0x00000005
HKR, Parameters\Device, SspInactivityTimeout, %REG_TYPE_DWORD%, 0x00000005
HKR, Parameters\Device, StpMaxOccupancyTimeout, %REG_TYPE_DWORD%, 0x00000005
HKR, Parameters\Device, SspMaxOccupancyTimeout, %REG_TYPE_DWORD%, 0x00000014
HKR, Parameters\Device, NoOutBoundTaskTimeout, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, IgnoreFUA, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, PerformanceOptimizationsEnable, %REG_TYPE_DWORD%, 0x00000000
;
HKR, Parameters\Device, InterruptCoalescingSampleSize, %REG_TYPE_DWORD%, 0x0000000a
HKR, Parameters\Device, InterruptCoalescingSampleFrequency, %REG_TYPE_DWORD%, 0x00000064
HKR, Parameters\Device, InterruptCoalescingThreshold, %REG_TYPE_DWORD%, 0x00002800
HKR, Parameters\Device, InterruptCoalescingLowNumber, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, InterruptCoalescingLowTimeout, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, InterruptCoalescingHighNumber, %REG_TYPE_DWORD%, 0x00000010
HKR, Parameters\Device, InterruptCoalescingHighTimeout, %REG_TYPE_DWORD%, 0x00000002
;
;;; Add the Phy specific user parameters
HKR, Parameters\Device, Phy0NotifyEnableSpinupInsertionFrequency, %REG_TYPE_DWORD%, 0x00000033
HKR, Parameters\Device, Phy0AlignInsertionFrequency, %REG_TYPE_DWORD%, 0x0000007f
HKR, Parameters\Device, Phy0InConnectionAlignInsertionFrequency, %REG_TYPE_DWORD%, 0x000000ff
HKR, Parameters\Device, Phy1NotifyEnableSpinupInsertionFrequency, %REG_TYPE_DWORD%, 0x00000033
HKR, Parameters\Device, Phy1AlignInsertionFrequency, %REG_TYPE_DWORD%, 0x0000007f
HKR, Parameters\Device, Phy1InConnectionAlignInsertionFrequency, %REG_TYPE_DWORD%, 0x000000ff
HKR, Parameters\Device, Phy2NotifyEnableSpinupInsertionFrequency, %REG_TYPE_DWORD%, 0x00000033
HKR, Parameters\Device, Phy2AlignInsertionFrequency, %REG_TYPE_DWORD%, 0x0000007f
HKR, Parameters\Device, Phy2InConnectionAlignInsertionFrequency, %REG_TYPE_DWORD%, 0x000000ff
HKR, Parameters\Device, Phy3NotifyEnableSpinupInsertionFrequency, %REG_TYPE_DWORD%, 0x00000033
HKR, Parameters\Device, Phy3AlignInsertionFrequency, %REG_TYPE_DWORD%, 0x0000007f
HKR, Parameters\Device, Phy3InConnectionAlignInsertionFrequency, %REG_TYPE_DWORD%, 0x000000ff
HKR, Parameters\Device, Controller0Phy0MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller0Phy1MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller0Phy2MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller0Phy3MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller1Phy0MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller1Phy1MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller1Phy2MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
HKR, Parameters\Device, Controller1Phy3MaxSpeedGeneration, %REG_TYPE_DWORD%, 0x00000002
;
;;; Add the Port specific OEM parameters
HKR, Parameters\Device, OemHeaderVersion, %REG_TYPE_DWORD%, 0x00000010
HKR, Parameters\Device, Controller0OemModeType, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemConcurrentDeviceSpinUpCount,%REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemSscEnable, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller0OemPort0PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller0OemPort1PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller0OemPort2PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller0OemPort3PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller0OemPhy0SasAddressLow, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemPhy0SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller0OemPhy1SasAddressLow, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemPhy1SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller0OemPhy2SasAddressLow, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemPhy2SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller0OemPhy3SasAddressLow, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller0OemPhy3SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller0OemPhy0AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller0OemPhy0AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller0OemPhy0AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller0OemPhy0AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller0OemPhy1AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller0OemPhy1AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller0OemPhy1AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller0OemPhy1AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller0OemPhy2AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller0OemPhy2AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller0OemPhy2AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller0OemPhy2AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller0OemPhy3AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller0OemPhy3AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller0OemPhy3AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller0OemPhy3AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
;
HKR, Parameters\Device, Controller1OemModeType, %REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller1OemConcurrentDeviceSpinUpCount,%REG_TYPE_DWORD%, 0x00000001
HKR, Parameters\Device, Controller1OemSscEnable, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller1OemPort0PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller1OemPort1PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller1OemPort2PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller1OemPort3PhyMask, %REG_TYPE_DWORD%, 0x00000000
HKR, Parameters\Device, Controller1OemPhy0SasAddressLow, %REG_TYPE_DWORD%, 0x00000004
HKR, Parameters\Device, Controller1OemPhy0SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller1OemPhy1SasAddressLow, %REG_TYPE_DWORD%, 0x00000004
HKR, Parameters\Device, Controller1OemPhy1SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller1OemPhy2SasAddressLow, %REG_TYPE_DWORD%, 0x00000004
HKR, Parameters\Device, Controller1OemPhy2SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller1OemPhy3SasAddressLow, %REG_TYPE_DWORD%, 0x00000004
HKR, Parameters\Device, Controller1OemPhy3SasAddressHigh, %REG_TYPE_DWORD%, 0x5FCFFFFF
HKR, Parameters\Device, Controller1OemPhy0AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller1OemPhy0AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller1OemPhy0AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller1OemPhy0AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller1OemPhy1AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller1OemPhy1AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller1OemPhy1AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller1OemPhy1AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller1OemPhy2AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller1OemPhy2AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller1OemPhy2AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller1OemPhy2AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, Controller1OemPhy3AfeTxAmpControl0, %REG_TYPE_DWORD%, 0x000BDD08
HKR, Parameters\Device, Controller1OemPhy3AfeTxAmpControl1, %REG_TYPE_DWORD%, 0x000B7069
HKR, Parameters\Device, Controller1OemPhy3AfeTxAmpControl2, %REG_TYPE_DWORD%, 0x000B7C09
HKR, Parameters\Device, Controller1OemPhy3AfeTxAmpControl3, %REG_TYPE_DWORD%, 0x000AFC6E
HKR, Parameters\Device, BackplaneIsPassive, %REG_TYPE_DWORD%, 0x00000000
;******************************************************************************
;*
;* INF FILE STRINGS (VARIABLES)
;*
;* This section specifies variables that can be reused elsewhere in this
;* INF file.
;*
;******************************************************************************
[Strings]
;;; *******Localizable Strings*******
diskId1 = "iaStorS Installation Disk"
Intel_SAS_RAID.Desc = "Intel(R) C600 Series Chipset SAS RAID Controller"
Intel_SATA_RAID.Desc = "Intel(R) C600 Series Chipset SAS RAID (SATA mode)"
INTEL = "Intel Corporation"
;
;;; *******Non Localizable Strings*******
SERVICE_BOOT_START = 0x0
SERVICE_SYSTEM_START = 0x1
SERVICE_AUTO_START = 0x2
SERVICE_DEMAND_START = 0x3
SERVICE_DISABLED = 0x4
SERVICE_KERNEL_DRIVER = 0x1
;
SERVICE_ERROR_IGNORE = 0x0
SERVICE_ERROR_NORMAL = 0x1
SERVICE_ERROR_SEVERE = 0x2
SERVICE_ERROR_CRITICAL = 0x3
;
REG_TYPE_BINARY = 0x00000001
REG_TYPE_KEY_ONLY = 0x00000010
REG_TYPE_DWORD = 0x00010001
REG_TYPE_EXPAND_SZ = 0x00020000
;
SPSVCINST_ASSOCSERVICE = 0x00000002
欢迎光临 无忧启动论坛 (http://bbs.c3.wuyou.net/)
Powered by Discuz! X3.3