无忧启动论坛

标题: PE装完系统的硬盘盘符顺序和PE里的不一样，怎么调整一下？ [打印本页]

作者: CYBERLONER 时间: 2023-10-16 15:59
标题: PE装完系统的硬盘盘符顺序和PE里的不一样，怎么调整一下？
比如在PE里显示的是ABCD，但是装完系统就变成BACD了，每次还要控制面板里改一次

作者: aiya01 时间: 2023-10-16 16:15
选不使用“理顺盘符”工具的pe，让系统自动排列就行

作者: tanglf 时间: 2023-10-16 16:20
好像有工具的，搜一下

作者: CYBERLONER 时间: 2023-10-16 16:22

aiya01 发表于 2023-10-16 16:15
选不使用“理顺盘符”工具的pe，让系统自动排列就行

好像不行，我用过

作者: aiya01 时间: 2023-10-16 16:39

CYBERLONER 发表于 2023-10-16 16:22
好像不行，我用过

论坛里有好几种盘符理顺工具，最常见的是orderdrv批处理顺，还有的pe在pecmd.ini或其它文件中用pecmd理顺的。这些盘符“理顺”过的都有可能出现盘符错乱。
只要未理顺，pe下与正常系统的盘符应该是相同的，除非你多硬盘、多系统，有可能不同。

作者: ouzhzh 时间: 2023-10-16 16:47
我安装完后也出现了这个问题，有的盘符还不准修改

作者: rbwrbw 时间: 2023-10-16 16:49
多系统就是这个niao样

作者: c707221671 时间: 2023-10-16 16:50
用自带的磁盘工具进行盘符的替换

作者: gander6 时间: 2023-10-16 17:15
以DG为准，PA也行。随便找个小工具，更改一下即可。

作者: say_dude 时间: 2023-10-16 17:21
是多系统吗？貌似单系统好像没有遇到需要多次调整的

作者: yyz2191958 时间: 2023-10-16 17:37

say_dude 发表于 2023-10-16 17:21
是多系统吗？貌似单系统好像没有遇到需要多次调整的

我也是这样

作者: szwp 时间: 2023-10-16 17:45
AB是保留给软驱的，pe问题

作者: xinqingme 时间: 2023-10-16 17:47
我的SSD+机械硬盘每次重装系统后，盘符都会乱，LZ使用盘符理顺工具试试看

作者: duanwangye 时间: 2023-10-16 17:55
我用的坛子里a66大佬的PE,每次安装系统后也是这样，最后还是要自己手动理顺一下。

作者: petereda 时间: 2023-10-16 17:57
磁盘管理，手动更改

作者: wsdyleon 时间: 2023-10-16 18:18
winntsetup安装有保持顺序的选项

作者: vaf 时间: 2023-10-16 18:19
楼上正解.
没什么好工具的.

作者: yc2428 时间: 2023-10-16 19:01
系统盘符改不了

作者: lhc0688 时间: 2023-10-16 19:12
为了避免盘符错乱带来误操作，大多PE会使用调整盘符功能，但这样也会存在两个问题：
1、PE和实机桌面系统看到的盘符不一致，导致误操作；
2、PE盘符调整结果不符合使用者本意；

举个真实的例子：之前遇到有系统人为更改D盘保存有重要数据，PE启动后识别为C盘直接安装系统，导致数据丢失（有固态+机械盘）；

所以，PE中不论调整和不调整盘符，都会存在不合理情况，其结果都会导致误操作风险，特别是有固态+机械盘混合，多硬盘多分区情况；

解决办法：我个人使用的PE，添加了可选择理顺盘符，在PE启动进入桌面前，按住“Q”键可跳过理顺盘符，不按则默认理顺；

这样的好处是：
1、可以查看原始盘符，跟实机桌面系统对比（有的实机系统也可能人为调整过盘符）；
2、可以检查理顺前后的盘符状况，确定自动理顺是否合理；
对存在复杂硬盘环境的电脑，在正式安装系统前（主硬盘重新分区、格式化、执行安装等等前），建议先分别查看原始和理顺后的盘符，并与之前桌面系统对照，确保操作的磁盘、分区准确；

至于装好后的桌面系统，有两个办法盘符调整：
1、直接手动调整；
2、如果PE理顺结果正确，也可使用相同版本的理顺盘符程序进行自动理顺；

作者: 百虹 时间: 2023-10-16 19:23
diskpart，卸载分区/重新挂载，指定盘符。

作者: wfg1555 时间: 2023-10-16 19:25
我的笔记本电脑也是不显示盘符

作者: softwarezheng 时间: 2023-10-16 19:33
我的也是

作者: softwarezheng 时间: 2023-10-16 19:33
好像有工具啊

作者: yuyimeng1118 时间: 2023-10-16 21:23
你进PE后用安装工具装完系统重启前，先把PE的U盘拔下来！

作者: 94079490 时间: 2023-10-16 22:09

yuyimeng1118 发表于 2023-10-16 21:23
你进PE后用安装工具装完系统重启前，先把PE的U盘拔下来！

好像是有这么个方法

作者: zxqsn 时间: 2023-10-17 04:08
自己手动更改盘符就好了嘛

作者: aoyabing 时间: 2023-10-17 06:45
本帖最后由 aoyabing 于 2023-10-17 06:47 编辑

最下面有附件下载，解压后右键以管理员身份运行Orderdrv.Cmd，选择Y即可。

::Created by victor888, QQ:2511755859
::Special thanks to CLONECD
::Special thanks to all the testers who provided with valid test results.
::Ordering and showing drive letters by drive type

@echo off
SETLOCAL ENABLEEXTENSIONS
SETLOCAL ENABLEDELAYEDEXPANSION

set ver=2020-11-02

::If "AUTO" was set to "y", all messed drive letters will be re-ordered automaticly without nitification.
::If "AUTO" was set to "n", a notification will come out to ask for confirmation wether to re-order messed driver letters.

set AUTO=n

:: 1. "U" is the FIRST Removable USB Disk drive letter to be fixed just change it as you like.
:: 2. "T" is the FIRST USB CDROM drive letter to be fixed just change it as you like.
:: 3. Above drive letters must not be conflict with any other existing drive letters, otherwise error will happen.
:: 4. You may disable the function of fixing above drive letters simply by deleting them.

set USBCDROM=T
set USBDRV=U

:: Following notes are for the first hard disk that the system found.
set upactdrv=N
::1. "N" means do not put active partiction drive letter or driver letter which contains windows (x:\windows\system32\config) ahead of all hard drive letters.
::2. "Y" means put active partiction drive letter or driver letter which contains windows (x:\windows\system32\config) ahead of all hard drive letters.

set winfirst=N
::1. "N" means active partition drive letter will be the first driver letter among all driver letters as long as upactdrv is set to Y.
::2. "Y" means  driver letter which contains windows (x:\windows\system32\config) will be the first driver letter among all driver letters when  upactdrv is set to Y and no active partition drive letter exists.

pushd %~dp0

if %~d0 neq %systemdrive% (
  if not exist %temp%\%~nx0 (
copy %0 %temp%\ /y >nul
copy drvtype.exe %temp%\ /y >nul 2>&1
copy fsutil.exe %temp%\ /y >nul 2>&1
copy mountvol.exe %temp%\ /y >nul 2>&1
copy smartctl.exe %temp%\ /y >nul 2>&1
pushd %temp%\
call %~nx0
exit
  )
)

echo                Batch file for ordering messed drive letters.
echo                   V.!ver!, By Victor888 from WUYOU.NET
echo    ------------------------------------------------------------------
echo.
echo Here is detailed information:
echo.

::get all drive letters by fsutil.exe
call :fsutil
if defined ALLDRV (
  set ALLDRV=!ALLDRV:\=!
  set ALLDRV=!ALLDRV: =!
  set ALLDRV=!ALLDRV::=: !
)

echo All drive letters: %ALLDRV%

::get all volume mount points and their full paths and merge them
FOR /F %%a in ('mountvol ^|find "\"') do set mtvdrv=!mtvdrv! %%a

::get unique drive letters which contain ":"
set mtvdrv=%mtvdrv: =%
set mtvdrv=%mtvdrv:\\?\Volume= %
set mtvdrv=%mtvdrv:}\=}%

for %%a in (%mtvdrv%) do (
  for /f "delims=} tokens=1,2" %%b in ("%%a") do (
set drv=%%c
set ttmp=%%c
set ttmp=!ttmp:~-2,1!
if !ttmp! equ : set mtdrv=!mtdrv! !drv:~0,2!
  )
)

if defined mtdrv (
  set mtdrv=!mtdrv: =!
  set mtdrv=!mtdrv::=: !
  echo Mounted drive letters: !mtdrv!
)

::get virtual drive letters which has no mount point
set virdrv=%ALLDRV%
for %%a in (%mtdrv%) do (
  set virdrv=!virdrv:%%a=!
)

set virdrv=!virdrv: =!
if defined virdrv (
  set virdrv=!virdrv::=: !
  echo Virtual drive letters: !virdrv!
  for /f "tokens=3 delims=       " %%a in ('reg query HKLM\System\CurrentControlSet\Services\ISODrive\Parameters /s 2^>nul ^|find /i "drive"') do (
if %errorlevel% equ 0 (
   set indvir=%%a
   if defined indvir (
      for %%b in (!virdrv!) do (
      if /i !indvir!: equ %%b (
         echo The ULTRAISO produced drive letter %%b
      )
      )
   )
)
  )
)

::get hard disk drive letters, Dataram drive letters and fixed USB drive letters by clonecd's DRVTYPE.
for /f "tokens=1-5 delims=|" %%a in ('drvtype -a ^|find ":"') do (
  set diskorder=%%a
  set hdtype=%%b
  set gptmbr=%%c
  set isssd=%%d
  set strdrv=%%e
  set hddrv=

  smartctl -i /dev/pd%%a |find "rpm">nul||set isssd=SSD

  if not defined strdrv set strdrv=%%d

  for %%f in (!strdrv!) do (
set eachdrv=%%f
set eachdrv=!eachdrv:~1,2!!
if "!eachdrv:$=!"=="!eachdrv!" (
   set hddrv=!hddrv! !eachdrv!
   set order=!order! !diskorder!:%%f
)
  )

  set strdrv=!hddrv! rem added on Dec. 31, 2018

  set hdtype=!hdtype:Vmware=!
  if !hdtype! neq %%b (
set /a ii+=1
echo Vmware Internel !gptmbr! hard disk !ii! mount path: !hddrv!
set thddrv=!thddrv! !hddrv!
  ) else (
set hdtype=!hdtype:diskvirtual=!
if !hdtype! neq %%b (
   set /a rr+=1
   echo Virtual PC Internel !gptmbr! hard disk !rr! mount path: !hddrv!
   set thddrv=!thddrv! !hddrv!
) else (
   set "hdtype=!hdtype:Virtual=!"
   if !hdtype! neq %%b (
      set /a jj+=1
      echo Virtual !gptmbr! hard disk !jj! mount path: !hddrv!
      set virdrv=!virdrv! !hddrv!
   ) else (
      set hdtype=!hdtype:RAMDISK=!
      if !hdtype! neq %%b (
      set /a oo+=1
      echo RAMDISK !gptmbr! hard disk !oo! mount path: !hddrv!
      set virdrv=!virdrv! !hddrv!
      ) else (
      set hdtype=!hdtype:FIRADISK=!
      if !hdtype! neq %%b (
         set /a pp+=1
         echo FIRADISK !gptmbr! hard disk !pp! mount path: !hddrv!
         set firadrv=!firadrv! !hddrv!
      ) else (
         set hdtype=!hdtype:winvblock=!
         if /i !hdtype! neq %%b (
            set /a bb+=1
            echo WINVBLOCK !gptmbr! hard disk !bb! mount path: !hddrv!
            set winvdrv=!winvdrv! !hddrv!
         ) else (
            set hdtype=!hdtype:USB=!
            if /i !hdtype! neq %%b (
            set /a nn+=1
            set tmpsysdrv=!hddrv:%systemdrive%=!
            if /i !hddrv! neq !tmpsysdrv! (
               set usbsys=!hddrv!
            ) else (
               set uhddrv=!uhddrv! !hddrv!
            )
            echo Fixed USB !gptmbr! disk !nn! mount path: !hddrv!
            ) else (
            if "!isssd!"=="SSD" (
               set /a qq+=1
               echo Solid State !gptmbr! Hard disk !qq! mount path: !hddrv!
               set ssddrv=!ssddrv! !hddrv!
               if /i !upactdrv! neq N (
                  if !qq!==1 (
                  for %%f in (!strdrv!) do (
                     set "eachdrv=%%f"
                     if /i !winfirst! neq N (
                        if "!eachdrv:~-1!"=="$" (
                        if "!eachdrv:~-2,1!"==":" set actdrv=!eachdrv:~1,2!
                        )
                     ) else (
                        if exist %%f\Windows\System32\config (
                        set actdrv=%%f
                        )
                     )
                  )
                  )
               )
            ) else (
               set /a ll+=1
               set thddrv=!thddrv! !hddrv!
               echo Internal !gptmbr! hard disk !ll! mount path: !hddrv!
               if /i !upactdrv! neq N (
                  if !ll!==1 (
                  if not defined actdrv (
                     for %%f in (!strdrv!) do (
                        if /i !winfirst! neq N (
                        if "!eachdrv:~-1!"=="$" (
                           if "!eachdrv:~-2,1!"==":" set actdrv=!eachdrv:~1,2!
                        )
                        ) else (
                        if exist %%f\Windows\System32\config (
                           set actdrv=%%f
                        )
                        )
                     )
                  )
                  )
               )
            )
            )
         )
      )
      )
   )
)
  )
)

set newhddrv=!ssddrv! !thddrv! !firadrv! !winvdrv!
set allhddrv=!newhddrv! !uhddrv!

if defined virdrv (
  if defined allhddrv (
for %%a in (!virdrv!) do (
   for %%b in (!allhddrv!) do (
      if %%a equ %%b (
      set hdvir=!hdvir! %%a
      set virdrv=!virdrv:%%a=!
      )
   )
)
  )
)

if defined hdvir echo No mount point hard disk drive letters: !hdvir!

if defined actdrv set newhddrv=!actdrv! !newhddrv:%actdrv%=!

if defined allhddrv (
  set mthddrv=!allhddrv!
  if defined mtdrv (
set otherdrv=!mtdrv!
for %%a in (!mthddrv! !virdrv!) do set otherdrv=!otherdrv:%%a=!
set otherdrv=!otherdrv: =!

if defined otherdrv (
   set otherdrv=!otherdrv:%systemdrive%=!
   set otherdrv=!otherdrv::=: !
   echo Other mounted drive letters: !otherdrv!
)
  )
)

if defined otherdrv (
  for %%a in (%otherdrv%) do (
set docheck=
set mnreg=
for /f "skip=2 tokens=3 delims=       " %%b in ('reg query HKLM\SYSTEM\MountedDevices /v \DosDevices\%%a') do (
   set "mnreg=%%b"
   if defined mnreg (
      set first8=!mnreg:~0,8!
      if !first8! equ 5F003F00 set docheck=ok
      if !first8! equ 5C003F00 set docheck=ok
      if /i !docheck! equ ok (
      set mnreg=!mnreg:5C=#!
      set mnreg=!mnreg:5f=#!
      set mnreg=!mnreg:23=#!
      set mnreg=!mnreg:26=#!
      set mnreg=!mnreg:00=!
      for /f "tokens=2,3,7 delims=#" %%c in ("!mnreg!") do (
         set tpcode=%%c
         set drvcode=%%d
         set prodcode=%%e

         rem FDC
         if /i !tpcode! equ 464443 (
            set /a fd+=1
            set intflp=!intflp! %%a
            echo Internal Floppy Drive Letter: %%a
         )

         rem DAEMON TOOLS
         if /i !tpcode! equ 4454534F4654425553 (
            set dtdvd=!dtdvd! %%a
            echo Daemon Tools CD/DVD Drive Letter: %%a
         )

         rem IDE
         if /i !tpcode! equ 494445 (
            if /i !tpcode! neq !tpcode:4364526F6D=! (
            set /a id+=1
            set idedvd=!idedvd! %%a
            echo IDE CD/DVD ROM: %%a
            )
         )

         rem SCSI
         if /i !tpcode! equ 53435349 (
            if /i !drvcode! neq !drvcode:4364526F6D=! (
            if /i !prodcode! equ 5669727475616C (
               echo SCSI Virtual DVD ROM: %%a
               set msvirdvd = !msvirdvd! %%a
            ) else (
               echo SCSI CD/DVD ROM: %%a
               set /a id+=1
               set scsidvd=!scsidvd! %%a
            )
            )
         )

         rem USBSTOR
         if /i !tpcode! equ 55534253544F52 (
            if /i !drvcode! equ 4364526F6D (
            set /a id+=1
            set /a ud+=1
            set usbdvd=!usbdvd! %%a
            echo USB CD/DVD ROM: %%a
            )
            if /i !drvcode! equ 4469736B (
            set /a ur+=1
            set usbrem=!usbrem! %%a
            echo Removable USB "Disk" Drive letter: %%a
            )
         )

         rem STORAGE, also removable USB
         if /i !tpcode! equ 53544F52414745 (
            if /i !drvcode! equ 52656D6F7661626C654D65646961 (
            set /a ur+=1
            set usbrem=!usbrem! %%a
            echo Removable USB "Storage" Drive letter: %%a
            )
         )

         rem FIRA_DISK
         if /i !tpcode! equ 464952414449534B (
            if /i !drvcode! equ 53466C6F707079 (
            set /a fd+=1
            set firaflp=!firaflp! %%a
            echo FIRA Floppy Disk Drive letter: %%a
            )
            if /i !drvcode! equ 4344524F4D (
            set /a frd+=1
            set firadvd=!firadvd! %%a
            echo FIRA CD/DVD ROM: %%a
            )
         )

         rem WINV_BLOCK
         if /i !tpcode! equ 57696E56426C6F636B (
            if /i !drvcode! equ 52414D466C6F7070794469736B (
            set /a fd+=1
            set winvflp=!winvflp! %%a
            echo Winv Block Ram Floppy Disk Drive letter: %%a
            )
            if /i !drvcode! equ 52414D4F70746963616C44697363 (
            set /a wvd+=1
            set wvbkdvd=!wvbkdvd! %%a
            echo Winv Block Ram CD/DVD ROM: %%a
            )
            if /i !drvcode! equ 46696C654F70746963616C44697363 (
            set /a wvd+=1
            set wvbkdvd=!wvbkdvd! %%a
            echo Winv Block File CD/DVD ROM: %%a

            )
         )
      )
      )
   )
)
  )
)

set flpdrv=!intflp!!firaflp!!winvflp!

if defined usbdvd (
  set usbdvd=!usbdvd: =!
  set usbdvd=!usbdvd::=: !
  if !ud! geq 1 (
if defined USBCDROM (
   set tmpud=!usbdvd:%systemdrive%=!
   if defined tmpud (
      set FirstUD=!usbdvd:~0,1!
      if /i !USBCDROM! neq !FirstUD! (
      for /f %%a in ('mountvol !FirstUD!: /l') do (
         mountvol !FirstUD!: /d
         mountvol !USBCDROM!: %%a
         echo First USBCD ROM drive letter was set to: !USBCDROM!:
      )
      )
      set usbdvd=!usbdvd:~2!
   )
)
  )
)

set dvddrv=!scsidvd!!idedvd!!msvirdvd!!dtdvd!!usbdvd!

if defined flpdrv (
  set flpdrv=!flpdrv: =!
  set flpdrv=!flpdrv::=: !
  if !fd! gtr 1 (
echo ALL Floppy drive letters: %flpdrv%
  )
)

set virdrv=!virdrv! !flpdrv!

if defined dvddrv (
  set dvddrv=!dvddrv: =!
  set dvddrv=!dvddrv::=: !
  if !id! gtr 1 (
echo ALL DVD/CD drive letters: %dvddrv%
  )
)

if defined firadvd (
  set firadrv=!firadvd: =!
  set firadvd=!firadvd::=: !
  if !frd! gtr 1 (
echo ALL Virtual Firadisk Optical drive letters: %firadvd%
  )
)

if defined wvbkdvd (
  set wvbkdvd=!wvbkdvd: =!
  set wvbkdvd=!wvbkdvd::=: !
  if !wvd! gtr 1 (
echo ALL Virtual Winvblock Optical drive letters: %wvbkdvd%
  )
)

if defined usbrem (
  set usbrem=!usbrem: =!
  set usbrem=!usbrem::=: !
  if !ur! gtr 1 (
echo ALL Removable USB drive letters: %usbrem%
  )
  if !ur! geq 1 (
if defined USBDRV (
   set tmprem=!usbrem:%systemdrive%=!
   if defined tmprem (
      set FirstU=!usbrem:~0,1!
      if /i !USBDRV! neq !FirstU! (
      for /f %%a in ('mountvol !FirstU!: /l') do (
         mountvol !FirstU!: /d
         mountvol !USBDRV!: %%a
         echo First removable USB disk drive letter was set to: !USBDRV!:
      )
      )
      set usbrem=!usbrem:~2!
   )
)
  )
)

echo SYSTEM DRIVE LETTER: %systemdrive%

if defined newhddrv (
  set totaldrv=%usbsys% %newhddrv% %dvddrv% %uhddrv% %usbrem% %wvbkdvd% %firadvd%
) else (
  set totaldrv=%usbsys% %uhddrv% %usbrem% %dvddrv% %wvbkdvd% %firadvd%
)

set totaldrv=!totaldrv:%systemdrive%=!

if defined virdrv (
  for %%a in (!virdrv!) do set totaldrv=!totaldrv:%%a=!
  set virdrv=!virdrv::=!
)

set totaldrv=!totaldrv: =!
set totaldrv=!totaldrv::=: !

if defined totaldrv set totaldrv=!totaldrv::=!

set fulldrv=CDEFGHIJKLMNOPQRSTUVWXYZ

for %%a in (%virdrv%) do set fulldrv=!fulldrv:%%a=!
set fulldrv=!fulldrv:%systemdrive:~0,1%=!

::ordering drive letters start
set /a kk=-1
for %%a in (%totaldrv%) do (
  set /a kk=kk+1
  call :olddrv %%a
)

if defined ordereddrv (
  if /i !AUTO! equ n (
echo DRIVE LETTERS to be ordered: %ordereddrv:~0,-1%
set /p doorder="Are you sure to make above drive letter changes (Y/N)"
if /i !doorder! equ y (
   call :mountbegin
   if errorlevel 0 (
      echo "Drive letter changing succeeded!"
   ) else (
      echo "Error happened, please check no drive letter used when changing begin!"
   )
) else (
   echo Drive letter changing cancelled by user!
)
  ) else (
call :mountbegin
  )
) else (
  echo DRIVE LETTER ORDER IS CORRECT.
)

if %~d0 neq %systemdrive% (
  if exist %temp%\drvtype.exe del %temp%\drvtype.exe
  if exist %temp%\smartctl.exe del %temp%\smartctl.exe
  if exist %temp%\mountvol.exe del %temp%\mountvol.exe
  if exist %temp%\fsutil.exe del %temp%\fsutil.exe
  if exist %temp%\%~nx0 del %temp%\%~nx0
)

pushd %~dp0

if !AUTO! equ n (
  pause
  goto :end
) else (
  goto :end
)
goto :end

:olddrv
set nk=!fulldrv:~%kk%,1!
if /i %1 neq !nk! (
  set ordereddrv=!ordereddrv! %1: to !nk!:,
)
goto :eof

:mountbegin
set ordereddrv=!ordereddrv:to=!
set ordereddrv=!ordereddrv: =!
set ordereddrv=!ordereddrv:,= !

for %%a in (!ordereddrv!) do (
  set oldnew=%%a
  call :vid_drv !oldnew:~0,1! !oldnew:~-2,1!
)

for %%a in (!ordereddrv!) do (
  set oldnew=%%a
  mountvol !oldnew:~0,2! /d
)

for %%a in (!newvid!) do (
  set eachnewvid=%%a
  set tmpeachnewvid=!eachnewvid:~0,1!
  if !tmpeachnewvid! neq { (
pecmd show !eachnewvid:~0,-1!,!eachnewvid:~-1!
  ) else (
mountvol !eachnewvid:~-1!: \\?\Volume!eachnewvid:~0,-1!\
  )
)

goto :eof

:dsptdrv
set dpd=
for %%a in (!order!) do (
  set eachdpd=%%a
  set tmpeachdpd=!eachdpd:%1=!
  if !eachdpd! neq !tmpeachdpd! (
if !eachdpd:~-1! neq $ (
   set dpd=!eachdpd:~0,-2!
) else (
   set dpd=!eachdpd:~0,-3!
)
  )
)
goto :eof

:vid_drv
set aa=%1
if defined hdvir (
  set tmphdvir=!hdvir:%1=!
  if !hdvir! neq !tmphdvir! (
call :dsptdrv !aa!
set newvid=!newvid! !dpd!%2
  ) else (
for /f %%b in ('mountvol %1: /l') do (
   set tmp=%%b
   set tmp=!tmp:\\?\Volume=!
   set tmp=!tmp:\=!
   set newvid=!newvid! !tmp!%2
)
  )
) else (
  for /f %%c in ('mountvol %1: /l') do (
set tmp=%%c
set tmp=!tmp:\\?\Volume=!
set tmp=!tmp:\=!
set newvid=!newvid! !tmp!%2
  )
)
goto :eof

:fsutil
   for /f "delims=:\ " %%a in ('fsutil.exe fsinfo drives^|more') do (
      set tmpdrv=%%a
      if !tmpdrv:~-2! equ %%a set ALLDRV=!ALLDRV! %%a:
   )
goto :eof

:end

Orderdrv.7z

4.33 KB, 下载次数: 20, 下载积分: 无忧币 -2

作者: cao8mm 时间: 2023-10-17 09:18
每次手动改一下就行，又不是天天装系统

作者: c5215016 时间: 2023-10-17 09:18
好

作者: CYBERLONER 时间: 2023-10-17 09:24

aoyabing 发表于 2023-10-17 06:45
最下面有附件下载，解压后右键以管理员身份运行Orderdrv.Cmd，选择Y即可。

::Created by victor888, QQ: ...

大神厉害，感谢分享

作者: 扬帆128 时间: 2023-10-17 09:25
我是用分区工具再次修改过来

作者: ppll2030 时间: 2023-10-17 09:27
使用同一个盘符调整脚本即可啊。如果习惯PE的，就把PE内的盘符调整脚本拷贝出来，安装系统后运行一次即可。

作者: jimson 时间: 2023-10-17 09:49
安装完系统后手动改一下就可以了，或者从安装系统到进入桌面前单硬盘安装，安装完成后再接上其它硬盘

作者: 铿锵玫瑰 时间: 2023-10-17 09:57
不是天天装系统,手动改一下就好！

作者: hipengcheng 时间: 2023-10-18 11:39
以DG为准，PA也行。随便找个小工具，更改一下即可。

作者: nowayer 时间: 2023-11-16 06:01
提示: 作者被禁止或删除内容自动屏蔽

作者: zpwz 时间: 2023-12-6 12:11
重启前拔起U盘。
或装完系统再接第二个硬盘

作者: hehuiying 时间: 2024-4-23 06:40
谢谢分享

欢迎光临无忧启动论坛 (http://bbs.c3.wuyou.net/)