目前论坛服务器主板的BIOS比较老旧，因为服务器在机房，不方便升级BIOS，并且考虑稳定性，也就错过了最佳时间升级。
如果不升级BIOS，可能会影响后期的使用PCIe转接的nvme 固态硬盘，及CPU的升级可选项。
不知谁能找到合适的BIOS升级固件？
主板开机信息如下：
Copyright (c) 2009 -2012 Intel Corporation. All rights reserved. Version 2.00.1201. Copyright (C) 2010 -2012 American Megatrends, Inc. BIOS：SE5C600.86B.01.03.0002.062020121504 BMC Firmware Version: 1.10.3560 SDR Version: SDR Package D.23 ME Firmware Version: 2.1.5.107 Platform ID: S2400SC
从开机信息来看，这是intel S2400SC主板，2012年左右的产品。 2022年时，曾经下载过 bios_r02.06.0007_package_romley_platforms.zip 这个文件，现在手中有这个文件。 但现在看这个文件的升级说明，需要先升级 BIOS 02.06.0006 才可以，现在也找不到这个BIOS 02.06.0006 可下载的固件。 从其他信息查询来看，是需要升级 BIOS_R03.01.0005_package_Romley_Platforms.zip 这个固件。 这些在intel 官网都找不到下载点。 不知谁能找到有用文件？
附 bios_r02.06.0007_package_romley_platforms.zip 里面的Update_Instructions.txt 说明文档：
EFI BIOS Update Package Installation and Operation Instructions BIOS Update Package Update Instructions
Released - Nov 01, 2018
******************************************************************************* This update package includes the following system software updates:
System BIOS - 02.06.0007
Important NOTES:
- All the updates provided in this package are EFI based (unless otherwise noted).To run these updates, you must boot the system to the embedded EFI shell and then access the USB flash drive or hard disk containing the system software updates.
************************************************************************************* SYSTEM HARDWARE and SOFTWARE REQUIREMENTS ************************************************************************************* The contents of this update package is used to update the BIOS for the following Intel Server Products only:
S2400BB S2600CP S2600CO W2600CR S2400EP S2400GP S2600GL S2600GZ S2600IP S2600JF S2400LP S2600KI S2400SC S2600WP S4600LH S1400SP S1400FP S1600JP
To update the system firmware to the versions included in this update package, the firmware currently loaded on the given server system must meet the following:
- BIOS 02.06.0006, or later Version
The utilities used to update the System Firmware are: - Iflash32 11.0 build 11
************************************************************************************* Standard Update Procedure from the embedded EFI Shell *************************************************************************************
- Unzip the contents of the update package and copy all files to a folder on a USB flash drive - Insert the USB flash drive to any available USB port on the server system to be updated - Boot the Server to the EFI shell. This can be accessed via the <F2> BIOS setup utility during POST. - Run the command "map -r" in the EFI shell to mount a USB flash drive formatted to use the FAT32 file system - Run the command "fs0:" to change folders to the USB flash drive. The USB flash drive may also mount to fs1: depending on other installed devices. The number of "fs#" is dependent on the result of command "map -r" - Change folders to the folder storing the update package files - Run the command "Startup.nsh" to start updating the BIOS updates
Warning: !!Do NOT reboot or remove power from your system during the update process. Doing so may render your system inoperable. !!
----- Verifying updates - Reboot the system - During POST, hit the <F2> Key when prompted to access the BIOS Setup Utility - Hit the F9 key to load BIOS Defaults - At the MAIN menu verify the BIOS revision is correct - Hit the F10 Key to save changes and Exit
The BIOS Update is Complete.
******************************************************************************* BIOS Recovery Process ******************************************************************************* In the unlikely event the BIOS is corrupted, leaving the system in an unbootable state, it may be necessary to perform the following BIOS Recovery procedure.
1. Copy the following BIOS update files to the root directory of a USB media device (Recovery Media): Note: These specific files will be located in the "BIOS Recovery Files" folder included in the System Update Package.
- IPMI.EFI - IFlash32.EFI - RML.ROM - R##.##.####REC.CAP (where ##.##.#### = BIOS revision number) - STARTUP.NSH (modified to support BIOS recovery)
2. Power OFF the system
3. Locate the BIOS Recovery Jumper on the server board and move the jumper block from pins 1-2 (default) to pins 2-3 (recovery setting)
4. Insert the recovery media into any available USB port on the back of the server Note: The front panel USB ports may not work for this procedure on some server systems.
5. Power ON the system
6. The system will automatically boot into the embedded EFI Shell
7. The STARTUP.NSH file automatically executes and initiates the flash update. When complete, the IFlash utility will display a message
8. Power OFF the system and return the BIOS Recovery jumper to its default position
9. Remove recovery media from the USB port
10. Power ON the system
11. Do *NOT* interrupt the BIOS POST during the first boot.
============================================================================= LEGAL INFORMATION ============================================================================= Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel Corporation may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel may make changes to specifications and product descriptions at any time, without notice.
Intel is a registered trademark of Intel Corporation. *Other names and brands are the property of their respective owners. Copyright (c) 2018 Intel Corporation.
A portion of this firmware is open source code, which falls under the GPL 2.0 license.
[END OF RELEASE NOTES]
| 
[复制链接]
IP卡
狗仔卡
发表于 
收藏
支持
反对
提升卡
沉默卡
喧嚣卡
变色卡
千斤顶
显身卡
发表于 
楼主